Home » Catalog » Special Tools, Tech Manuals » Coring Drill  
Product Categories
Apparel
American Hardware
Pistons and Cylinders
Flywheels and Clutches
Gaskets and Bearings
Cranks, Rods and Gland Nuts
Oiling System
Valve Train
Pulleys
Carburetion
Programmable Fuel Injection
Electrical Parts
Cylinder Heads
Traction Bars and Mounts
Gear Sets, Tranny Parts, Suspension
5 Speed Kits
Special Tools, Tech Manuals
   � CASE SPLITTING TOOL
   � Hot VW's Magazine
   � Torque Multiplier
   � 17mm Trans Drain Tool
   � Flywheel Puller
   � Transmission Fixture Test Driver
   � Tools - Gene Berg Flycutter
   - Tools
   � Drill Press Flycutter
   - Tools
   � Mill Set
   � Additional Cutter Heads
   � Semi-Hemi Cutter
   � Special Centers
   � Lash Cap Puller
   � Replacement Blades
   � Boring - Deck Plate
   - Special Note
   � Valve Guide Boss Cutter
   � Off Road Race Engines Require a Seal
   - Technical Information
   � Pulley Seal Tool
   � Pulley Seals
   - Warning - No Bolt In Seal/Pulleys
   � Coring Drill
   � Ring Compressor Set
   � Gear Puller
   � Cam Follower - Case Hole Cutter
   � Flywheel Holder
   � End Play Measuring Tool
   � Universal Pulley Puller
   � Valve Spring Remover
   � Lifter Retaining Springs
   � Flywheel Seal Tool
   � Deck Measuring Tool
   � Oil Relief Cup Puller
   � Oil Filler Nut Wrench
   � Distributor Drive Puller
   � Axle Nut Driver Wrench
   � Clutch Cable Adjusting Wrench
   � Valve Adjusting Wrench
   � 22mm Piston Pin Driver
   � 8mm Guide Driver
   � Clutch Alignment Tools
   � CC Kits and Parts
   � Synchrometers
   � Flywheel - Crank Drill Fixture
   � Gear Ratio Computer
   - Ratio Computer
   � Books and Literature
   � Berg's Information Copyrighted Materials
   � Berg Book of Instructions
   � Berg Technical Sets
   - Individual Articles
   - Tech Articles
   � Individual Articles
   � Technical Materials
   � Have your own computer?
   � Gear Ratio Program
   - Gear Ratio Program
   � HP for DOS
   � California Look VW Book
   � Bentley VW Workshop Manuals

Exhaust Systems, Related Parts
Shifters and Related Parts
Wheelie Bars, Anti-shocker, Drag Fans
Welded Balance Cooling Fans
Type IV Tin Conversion
Shop Supplies
Cases and Related Parts
Labor Section
Factory Volkswagen Parts
Complete Engine Kits
Oils
Metric Hardware

Location: Home » Catalog » Special Tools, Tech Manuals » Coring Drill

Coring Drill


     Product Name   Description   MSRP Price   Our Price+   Cash Price 
     GB 712  8mm M42 cobalt coring drill. Cores standard 8mm guides. Why a coring drill? Because it is the only proper way I know of to remove a guide from the head without swelling or damaging the guide hole in the head. For years I was frustrated with having the guides come loose in the heads after a few thousand miles. I had the guide holes measured with some electronic bore gauges and found out that they were not straight, round or the same size from one end to the other any more. The aircraft engineer suggested that we core the guide 75% to 85% of the way and then drive it out to eliminate this problem. It did eliminate it. We also discovered that race heads which had the bosses cut would come right out without breaking the boss off. This slick tool does just that by first spot facing the spring end of the guide flat with our GB 706 (be sure all of the guide head is removed) to the aluminum boss and coring from the spring side 75% to 80% of the way through the old guide. You can then tap out the guide with an old 10mm head stud with no damage to the head. The new guide will now be straight in the hole with the proper press fit from one end to the other. Remember, even bosses cut for inner and outer springs are not normally broken or damaged with this procedure. The Berg coring drill resists breakage due to an exclusive design. Provides years of trouble free service and can be resharpened. Also available in 9mm as GB 712-9 Made in USA by Gene Berg Enterprises.   $55.73   $37.95   $37.95 
     GB 712-9  9mm M42 cobalt coring drill. Cores standard 9mm guides. Why a coring drill? Because it is the only proper way I know of to remove a guide from the head without swelling or damaging the guide hole in the head. For years I was frustrated with having the guides come loose in the heads after a few thousand miles. I had the guide holes measured with some electronic bore gauges and found out that they were not straight, round or the same size from one end to the other any more. The aircraft engineer suggested that we core the guide 75% to 85% of the way and then drive it out to eliminate this problem. It did eliminate it. We also discovered that race heads which had the bosses cut would come right out without breaking the boss off. This slick tool does just that by first spot facing the spring end of the guide flat with our GB 706 (be sure all of the guide head is removed) to the aluminum boss and coring from the spring side 75% to 80% of the way through the old guide. You can then tap out the guide with an old 10mm head stud with no damage to the head. The new guide will now be straight in the hole with the proper press fit from one end to the other. Remember, even bosses cut for inner and outer springs are not normally broken or damaged with this procedure. The Berg coring drill resists breakage due to an exclusive design. Provides years of trouble free service and can be resharpened. Also available in 8mm as GB 712. Made in USA by Gene Berg Enterprises.   $49.00   $39.95   $39.95 
    Displaying 1 to 2 (of 2 products) Result Pages:  1 

     

     

    Quick Find
     
    Use keywords to find the product you are looking for.
    Advanced Search
    Information
    Business Hours
    Phone Service
    Placing Orders
    Shipping Policies
    Returns For Credit
    Warranty Policy
    Privacy Notice
    Disclaimers
    Contact Us

    Web design and hosting by Canvas Dreams LLC and California web design by Pearl Compass.

    Please contact us about errors or questions. We value your input!

    Any and all references to the company Volkswagen, or the VW name are strictly for reference only. The GENE BERG name and GENE BERG products are protected under trademark, copyright and patent law, any violations will be pursued. GENE BERG ENT. is not a part of any companies mentioned or linked to this website and any beliefs of those companies are not necessarily the beliefs of GENE BERG ENTERPRISES.

    Copyright ©2024 GENE BERG ENTERPRISES all rights reserved