Home » Catalog » Special Tools, Tech Manuals » Have your own computer?  
Product Categories
American Hardware
Pistons and Cylinders
Flywheels and Clutches
Gaskets and Bearings
Cranks, Rods and Gland Nuts
Oiling System
Valve Train
Programmable Fuel Injection
Electrical Parts
Cylinder Heads
Traction Bars and Mounts
Gear Sets, Tranny Parts, Suspension
5 Speed Kits
Special Tools, Tech Manuals
   � Hot VW's Magazine
   � Torque Multiplier
   � 17mm Trans Drain Tool
   � Flywheel Puller
   � Transmission Fixture Test Driver
   � Tools - Gene Berg Flycutter
   - Tools
   � Drill Press Flycutter
   - Tools
   � Mill Set
   � Additional Cutter Heads
   � Semi-Hemi Cutter
   � Special Centers
   � Lash Cap Puller
   � Replacement Blades
   � Boring - Deck Plate
   - Special Note
   � Valve Guide Boss Cutter
   � Off Road Race Engines Require a Seal
   - Technical Information
   � Pulley Seal Tool
   � Pulley Seals
   - Warning - No Bolt In Seal/Pulleys
   � Coring Drill
   � Ring Compressor Set
   � Gear Puller
   � Cam Follower - Case Hole Cutter
   � Flywheel Holder
   � End Play Measuring Tool
   � Universal Pulley Puller
   � Valve Spring Remover
   � Lifter Retaining Springs
   � Flywheel Seal Tool
   � Deck Measuring Tool
   � Oil Relief Cup Puller
   � Oil Filler Nut Wrench
   � Distributor Drive Puller
   � Axle Nut Driver Wrench
   � Clutch Cable Adjusting Wrench
   � Valve Adjusting Wrench
   � 22mm Piston Pin Driver
   � 8mm Guide Driver
   � Clutch Alignment Tools
   � CC Kits and Parts
   � Synchrometers
   � Flywheel - Crank Drill Fixture
   � Gear Ratio Computer
   - Ratio Computer
   � Books and Literature
   � Berg's Information Copyrighted Materials
   � Berg Book of Instructions
   � Berg Technical Sets
   - Individual Articles
   - Tech Articles
   � Individual Articles
   � Technical Materials
   � Have your own computer?
   � Gear Ratio Program
   - Gear Ratio Program
   � HP for DOS
   � California Look VW Book
   � Bentley VW Workshop Manuals

Exhaust Systems, Related Parts
Shifters and Related Parts
Wheelie Bars, Anti-shocker, Drag Fans
Welded Balance Cooling Fans
Type IV Tin Conversion
Shop Supplies
Cases and Related Parts
Labor Section
Factory Volkswagen Parts
Complete Engine Kits
Metric Hardware

Location: Home » Catalog » Special Tools, Tech Manuals » Have your own computer?

Have your own computer?

    Do you wish to have the ability to calculate CR and gas octane needs of engines and/or the gear ratios vs. tire diameter, RPM and MPH, or even the HP your engine is making when you know the 1/8 or 1/4 mile ET or vice versa on your own computer? I offer a ratio program written in Turbo Basic that performs all of these tasks "FAST".
    The CR program allows you to enter by prompt; the bore in mm, stroke in mm, piston notches (if any) in cc, deck in inches, and head cc. It also prompts you to calculate what head or deck is needed to achieve a specific compression ratio. That's right, it figures it out and tells you what it takes so you do not need to keep calculating to get to a specific number. It calculates engine size in cc and cu. in., deck volume in cc, CR based on your entry and gives the mathematical octane requirement for the engine to live its longest. If using a Semi-Hemi cut head you can run 0.3 CR higher than this program tells you to use. You may then select by menu to return to a new deck or head calculation for the same size engine or from a new size engine.
    You can also select from the menu to enter the gear ratio chart calculations. The gear ratio prompts you, "Do you know the ratios already or do you need to input the actual tooth count of the gears?" If you need to input the tooth count it calculates the ratios of R/P, 1st, 2nd, 3rd, and 4th. It lists them on the screen so you can enter them at the prompt. You then enter as asked for; R/P, 1st, 2nd, 3rd, 4th, tire height, start chart RPM at, choice of 50, 100, 200, 300, 500 increments, and ending RPM of chart. The screen chart can then be used to see what the RPM drop is from gear to gear or the chart can be printed.
    Next, we have added the ability to do drag race calculations for both the 1/8 and 1/4 miles. You must know either the HP or the ET of the car and the weight of the car as it is raced with the driver. If you know the ET and weight it will tell you what your engine is making for HP. Naturally, the program was designed for proper gearing to take advantage of the engine's power. Readings will not be as accurate without close ratio gears.
    All of these programs can be printed out on standard size printers (80 column). All instructions are included to get it up and running on the label and the READ.ME document file on the disk. Developed by Bill Greenwood and Gene Berg.

    There are no products to list in this category.



    Quick Find
    Use keywords to find the product you are looking for.
    Advanced Search
    Business Hours
    Phone Service
    Placing Orders
    Shipping Policies
    Returns For Credit
    Warranty Policy
    Privacy Notice
    Contact Us

    Web design and hosting by Canvas Dreams LLC and California web design by Pearl Compass.

    Please contact us about errors or questions. We value your input!

    Any and all references to the company Volkswagen, or the VW name are strictly for reference only. The GENE BERG name and GENE BERG products are protected under trademark, copyright and patent law, any violations will be pursued. GENE BERG ENT. is not a part of any companies mentioned or linked to this website and any beliefs of those companies are not necessarily the beliefs of GENE BERG ENTERPRISES.

    Copyright ©2024 GENE BERG ENTERPRISES all rights reserved