Home » Catalog » Oiling System » Full Flow Oil Pump Covers  
Product Categories
Apparel
American Hardware
Pistons and Cylinders
Flywheels and Clutches
Gaskets and Bearings
Cranks, Rods and Gland Nuts
Oiling System
   � JayCee Sump Plate
   � Oil Additives Mandatory
   � Oil Filler and Breather
   � Oil Filler and Breather Box
   � Factory Generator Mount breather box
   - Berg Breather Boxes
   � Factory Alternator Mount breather box
   - Berg Breather Boxes
   � Race Breather Box
   � Valve Covers Vented for Breather Boxes
   - Vented Valve Covers
   � Oil Sumps
   - Technical Information
   � Standard Street Sump
   - Berg Oil Sumps
   � Ultra High-performance Street and Race Sump
   � 4 Quart Drag Race Sump
   � Sump Parts for Current and Early Berg Sumps
   - Sump Parts
   � Added Bearing Life
   - Technical Information
   � Extra Pickup Tubes
   � Added Capacity
   - FYI
   � Cooling
   - FYI
   � Oil Coolers
   - Technical Information
   � Oil Cooler Block Off Plate
   - Cooler Off Block
   � Why we do not sell gauges
   - Technical Information
   � How to know when your engine is hot.
   � How GB 227 Works
   � Berg Oil Temperature Dip Sticks
   - Oil Temperature Dip Sticks
   � Oil Pumps
   - Oil Pumps and Gaskets
   � 26mm Oil Pumps
   - For all dual oil pressure cases
   - For early single oil pressure cases
   � 30mm Oil Pumps
   - For all dual oil pressure cases
   � Oil Pump O'ring
   � Gaskets
   - Warning:
   � Technical Information
   � Oil Pressure Relief Covers
   - Use with or without FF
   � Full Flow Oil Pump Covers
   - Standard Full Flow Covers
   � Full Flow Oil Filtering
   - Technical Information
   � Tools Required to drill and tap a case for full flow
   � Achieve full oil flow from a plugged pump
   - FYI
   � Filter on Inlet Side
   - Warning
   � Full Flow Oil Filter Kits
   - Stainless Steel AN8 Hose Kits
   � Neoprene Hose Kits
   - Neoprene Hose Full Flow Kits
   - Substitute GB 239
   � Relief Valve Cover Option
   - Substitute Relief Valve Cover Option
   � System One Option
   � System 1 Filters
   � System 1 Spare Parts
   � Oberg Filter Screen
   - O Berg Filter Parts
   � Taps, Reamers & Drills
   - Taps and Reamers
   � Separate Full Flow System Parts and Fittings
   - Filters and Filter Adapters
   � Don't Have a Blow Out
   � PTFE Hose, Covered with Stainless Steel AN-8 Oil Hoses
   - PTFE Tubing
   - Stainless Steel Hoses
   � Custom Oil and Gas Hoses
   - AN-6 Gas Lines
   - AN-8 Gas Lines
   � Ordering Custom Oil or Gas Hoses
   - FYI
   � AN Fittings
   � Pipe Fittings
   � Hose
   - Hose per foot
   - Warning
   � "T" Fittings/Nipples
   - Nipples
   - Tees
   � Plugs for Oil Galleries
   - Hose Clamps
   - Plugs for Berg GBF Crankshafts
   - Standard tapered pipe plugs

Valve Train
Pulleys
Carburetion
Programmable Fuel Injection
Electrical Parts
Cylinder Heads
Traction Bars and Mounts
Gear Sets, Tranny Parts, Suspension
5 Speed Kits
Special Tools, Tech Manuals
Exhaust Systems, Related Parts
Shifters and Related Parts
Wheelie Bars, Anti-shocker, Drag Fans
Welded Balance Cooling Fans
Type IV Tin Conversion
Shop Supplies
Cases and Related Parts
Labor Section
Factory Volkswagen Parts
Complete Engine Kits
Oils
Metric Hardware

Location: Home » Catalog » Oiling System » Full Flow Oil Pump Covers

Full Flow Oil Pump Covers

The only proper way to achieve full flow oil filtering without pressure or flow loss is to plug the pump, use a full flow cover, drill and tap the main oil gallery to return the oil. All other methods such as pump covers or pumps that have inlet and outlets all together at the pump reduce the pressure and flow of oil from stock and can cause damage or a premature failure to the engine.
The Berg covers are designed to work with any stock VW, 19, 21, 25, 26mm pump, all Berg pumps and any pump that can use a flat cover. Pumps must be plugged and the case drilled and tapped into the main oil gallery to be used for full flow.
Berg covers allow plumbing from the oil pump to a remote mounted oil filter and/or cooler. They are all drilled and tapped 3/8" NPT to match all of our fittings. This area is as short as possible to allow maximum clearance for mounts, pulleys, and tinware so that all fittings fit behind the tinware. Must be mounted with the outlet toward the 3 and 4 cylinder side of the car. We use only cast iron to prevent unwanted pressure losses from wear or improper expansion that an aluminum cover causes. Comes with exclusive Berg copyrighted instructions.
Note: If using on a Type III or 68-71 bus be sure to order the proper cover, relief cover (or full flow kit) from us that has the proper fittings already installed for the best mount clearance. Yes, they are our regular covers, however, require retapping and often extra clearancing must be done to get the fittings to end up in the correct location and to clear everything the best way possible without cracking the cover. Originated and manufactured by Gene Berg from 1972. SW 2#

 

 

Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
Information
Business Hours
Phone Service
Placing Orders
Shipping Policies
Returns For Credit
Warranty Policy
Privacy Notice
Disclaimers
Contact Us

Web design and hosting by Canvas Dreams LLC and California web design by Pearl Compass.

Please contact us about errors or questions. We value your input!

Any and all references to the company Volkswagen, or the VW name are strictly for reference only. The GENE BERG name and GENE BERG products are protected under trademark, copyright and patent law, any violations will be pursued. GENE BERG ENT. is not a part of any companies mentioned or linked to this website and any beliefs of those companies are not necessarily the beliefs of GENE BERG ENTERPRISES.

Copyright ©2024 GENE BERG ENTERPRISES all rights reserved