Home » Catalog » Adjusting Screw Info  
Product Categories
Apparel
American Hardware
Pistons and Cylinders
Flywheels and Clutches
Gaskets and Bearings
Cranks, Rods and Gland Nuts
Oiling System
Valve Train
    Oil Additives Mandatory
    Street Valve Springs
   - Technical Information
    Race Springs
   - Triple, Stock OD
    Valve Springs Stock OD
   - Single HD
    Chevy Type-1.4374" OD Inner and Outer Springs
    Dual - Inner & Outer, Stock OD
    Sets of Springs, Retainers & Shims
   - Spring Sets
    Valve Spring Retainers
   - Valve Retainers
    Valve Spring Shims
   - Valve Spring Sims
    Valve Springs
   - Technical Information
    Springs Require Stronger Steel Pushrods- Warning
   - Warning
    Mandatory Reading About Cam Sense
   - Technical Information
    Berg New Billet Cams
    High Performance Cams
   - Designed for VW Stock Ratio Rocker Arms with Factory 1.1:1 Ratio
    Camshafts for 1.1:1 Rockers
    Start of Camshafts
   - Camshaft only
    Cams Designed for 1.4, 1.45, 1.45, 1.54, Up to 1.65 Ratio Rockers
    All Cams Below Require:
    Camshaft to Berg Stroker Crankshaft Clearance
   - Technical Tip
    Cam Bolt Set
    Cam Lube
    Cam Followers (Lifters)
    Case Bushings
    Wide Base Lifters
    Reground Lifters
    Case Modification of Hydraulic Lifters
    At this time we do not sell any hydraulic lifters
    Cam Gears
    Berg Adjust-A-Gear
    Adjust-A-Gear Washers
    Straight Cut Cam Gears
   - Technical Information
    Adjusting Screws
   - Adjusting Screw Info
    Gene Berg Cup Screws
    Super Duty Valve Keepers
    Valves, Stock Size
   - Stock Size Valves Each
    Manley Valves, Oversize
   - Manley Stainless Steel Valves Each
    Other Stainless Valves
   - Stainless Steel Valves ea. ("NON" Manley one piece SS valves. Excellent quality.)
    Valve Guides
   - Valve Guides and Boss
    Stock Length Titanium Valves
   - Titanium Valves Ea. Std. VW 3 Groove
    Titanium Valves with 0.0100" Longer Stem
   - Titanium Plus 0.100"
    Valve Lash Caps
    Lash Cap Puller
    Valve Seats for Oversized Valves
   - Steel Valve Seats (Works with unleaded gas)
    Silicon Aluminum Bronze Valve Seat Material
   - Brass Seat Material (Sold by the ounce.)
    Rocker Arm Thrust Washers
   - Thrust Washers
    Rocker Arm Geometry Shims
   - Rocker Stand Shims
    Geometry Shims Berg Ratio Rockers
    Been Clipped Lately?
   - Technical Information
    Heavy Duty Rocker Arm Shaft Kits
    Heavy Duty Rocker Arm Shaft Studs
    Gene Berg Forged High Ratio Rockers
   - Gene Berg Forged Rockers
    Proper Bushing Used
    Super Quality Adjusting Screws
    Why a Ratio Rocker Arm?
    Gene Berg Forged Rocker Sets
   - Sets Include
    Special Sets for Moved Exhaust Valves
    Valve Lift
   - Technical Information
    What about 1.2 and 1.25 Rockers - FYI
    Roller Tip Rockers - FYI
    What Valve Covers to Use
    Carbon Fiber Pushrods
   - Technical Information
    Noisy Steel Pushrods? Special FYI
    How to Make Your Own Test Pushrod - Technical Tip
    80,000 PSI Pushrod Kits
   - Pushrods 80,000 PSI
   - Warning
    About Aluminum Pushrods
    Superduty 160,000 PSI Racing Pushrods
   - Race Pushrods 160,000 PSI .042" Wall

Pulleys
Carburetion
Programmable Fuel Injection
Cylinder Heads
Electrical Parts
Traction Bars and Mounts
Gear Sets, Tranny Parts, Suspension
5 Speed Kits
Special Tools, Tech Manuals
Exhaust Systems, Related Parts
Shifters and Related Parts
Wheelie Bars, Anti-shocker, Drag Fans
Welded Balance Cooling Fans
Type IV Tin Conversion
Shop Supplies
Cases and Related Parts
Labor Section
Factory Volkswagen Parts
Complete Engine Kits
Oils
Metric Hardware

Location: Home » Catalog » Adjusting Screw Info

Adjusting Screw Info

    Berg's special type screws with swivel head like 911S Porsche, fit under stock VW valve covers. Often called elephant feet. Suggested for all VW engines using the standard rocker arm configuration because they decrease side load and wear of the valve guides and stems. Furthermore, they provide a completely flat contact surface to prevent stem damage often related to stock type adjusting screws. A must for all cams with over 0.400" lift at the valve and provide longer life even with a stock engine. Precision ground on the foot to provide proper contact area. Stops all stem wear normally present with regular screws. No need for lash caps when you use these.


     Product Name   Description   MSRP Price   Our Price+   Cash Price 
     GB 340A  Single Berg swivel screw for stock 8mm VW rocker arms.   $0.00   $24.75   $0.00 
     GB 340NUT  VW 8mm jam nut   $0.00   $0.52   $0.00 
     GB 341A  Set of 8 GB 340A including the required amount of GB 403 shims to maintain correct geometry. Pushrods do not need to be cut and rocker arms do not need to be weakened by grinding part of it away. Flat-blade screwdriver head. Berg copyrighted installation instructions included. Requires GB 340NUT   $0.00   $176.90   $0.00 
    Displaying 1 to 3 (of 3 products) Result Pages:  1 

     

     

    Quick Find
     
    Use keywords to find the product you are looking for.
    Advanced Search
    Information
    Business Hours
    Phone Service
    Placing Orders
    Shipping Policies
    Returns For Credit
    Warranty Policy
    Privacy Notice
    Disclaimers
    Contact Us

    Web design and hosting by Canvas Dreams LLC and California web design by Pearl Compass.

    Please contact us about errors or questions. We value your input!

    Any and all references to the company Volkswagen, or the VW name are strictly for reference only. The GENE BERG name and GENE BERG products are protected under trademark, copyright and patent law, any violations will be pursued. GENE BERG ENT. is not a part of any companies mentioned or linked to this website and any beliefs of those companies are not necessarily the beliefs of GENE BERG ENTERPRISES.Site maintained by xanax side effects

    Copyright ©2014 GENE BERG ENTERPRISES all rights reserved