Home » Catalog » Caster Wedges/ Bolts  
Product Categories
Apparel
American Hardware
Pistons and Cylinders
Flywheels and Clutches
Gaskets and Bearings
Cranks, Rods and Gland Nuts
Oiling System
Valve Train
Pulleys
Carburetion
Programmable Fuel Injection
Electrical Parts
Cylinder Heads
Traction Bars and Mounts
Gear Sets, Tranny Parts, Suspension
   � HD Spring Plate Retainer
   � Close Ratio Gear Sets - FYI
   � Syncro Installed and Welded
   � 3rd Gears
   - Close Ratio 3rd Gear Sets
   � 4th Gears
   - Close Ratio 4th Gear Sets
   � Berg Gear Copies - Warning
   � Liberty Pro Rings and Modified Sliders - FYI
   � Gearing
   - Technical Information
   � Gear Ratios
   � The Berg BUS 600 Adapter
   � Side Cover Savers
   � BUS 600A and BUS 600L Adapter
   � How Does It Bolt In?
   - Bus To Sedan Housing
   - Synchro Hub and Washer
   � Ring and Pinion Gear Sets
   - Aftermarket Ring & Pinion
   - Ring & Pinion Gears - Genuine VW Brazil
   � Modify Your IRS BUS 4.57:1
   � A Needle In A Haystack
   - Technical Information
   - Transaxle Parts
   � Super Beetle 3.78 Mainshaft/First Gear
   - Technical Tip
   � 3.78 Mainshaft
   � Conversion Bearing Kit
   � Super Duty Berg Close Ratio 1st and 2nd Gear Sets
   - Berg Mainshaft Sets
   � FTC Close Ratio 1st and Second Gear Sets
   � Heavy Duty Sleeve and Washer
   - Sleeve/ Washers
   � Super Duty Keys
   � Side Cover Savers2
   � Side Cover Nut Conversion
   � Side Covers
   � Pro Shift Parts
   - Liberty Pro Shift Parts
   - Technical Information
   � Super Duty Pinion Bearing Retainer
   - Pinion Bearing Retainers
   - Technical Information
   � We No Longer Sell Super Diffs
   � Super Duty Berg Axles Technical Tip
   - Axles (per pair)
   � Poor Man's Posi (Swingaxle only)
   - Technical Tip
   � Magnesium Plate
   - Mag Plate & Welding Rod
   � Caster Wedges
   - Caster Wedges/ Bolts
   � Avis Front End Adjuster
   - Avis Adjuster
   � Front Axle Beam with Adjusters

5 Speed Kits
Special Tools, Tech Manuals
Exhaust Systems, Related Parts
Shifters and Related Parts
Wheelie Bars, Anti-shocker, Drag Fans
Welded Balance Cooling Fans
Type IV Tin Conversion
Shop Supplies
Cases and Related Parts
Labor Section
Factory Volkswagen Parts
Complete Engine Kits
Oils
Metric Hardware

Location: Home » Catalog » Caster Wedges/ Bolts

Caster Wedges/ Bolts

    Caster wedges have been used by VW from the early 50's for cars that wandered in the wind or did not have enough caster from the factory. At least one set was a must if the car was to be driven over 75 MPH. Some cars are manufactured by VW that may have the minimum allowable caster. What this does is allows the car to wander as the speed gets higher or more than normal in a cross wind.
    People that lower the front end of their car, raise the rear end, or both, will aggravate this situation even more. I have seen lowered cars that were almost impossible to keep in one lane at 60 MPH. Some vehicles require more than one caster wedge just to get back to stock and even more to make it safe at 100 MPH. You may need one set of our 3.4 degree and one set of our 2.36 degree. This all depends on the amount of lowering and the maximum speed the car will reach. By adding the proper amount of caster wedges, you tip the beam out at the bottom and increase the caster to eliminate wandering. It is impossible for anyone to guess what "your" car needs. We strongly recommended that the caster be checked before ordering to determine what you actually need. For more information on front and rear suspension see GB 801-SUSPENSION specifically for drag racing or fast street cars. Made in USA by Gene Berg Enterprises.
    Note: 1 One set of 2 is required for a front end unless you are adding wheel stagger to one side or correcting for a bent frame horn.
    Note: 2 GB 681 caster wedges that are 2.36 degrees are about 5.9mm thick and use the factory 90mm bolt. 3.4 degrees are about 8.6mm thick and use GB 681B 100mm long bolts. We also offer 110mm for applications that require stacking more caster wedges. You can calculate what you need by these measurements.
    Note: Shims can be stacked to achieve desired caster.


    1054 - Unknown column 'm.manufacturers_name' in 'order clause'

    select DISTINCT p.products_image, p.products_model, products_description.products_name, p.products_id, products_description.products_description, products_to_categories.categories_id, p.products_price, p.products_price_msrp, p.products_price_cash from products_description INNER JOIN products p ON products_description.products_id = p.products_id INNER JOIN products_to_categories ON products_to_categories.products_id = p.products_id where p.products_status = '1' and products_to_categories.categories_id = '2917' order by m.manufacturers_name , pd.products_name limit 0, 1000

    [TEP STOP]