Home » Catalog » Caster Wedges/ Bolts  
Product Categories
Apparel
American Hardware
Pistons and Cylinders
Flywheels and Clutches
Gaskets and Bearings
Cranks, Rods and Gland Nuts
Oiling System
Valve Train
Pulleys
Carburetion
Programmable Fuel Injection
Cylinder Heads
Electrical Parts
Traction Bars and Mounts
Gear Sets, Tranny Parts, Suspension
    Close Ratio Gear Sets - FYI
    Syncro Installed and Welded
    3rd Gears
   - Close Ratio 3rd Gear Sets
    4th Gears
   - Close Ratio 4th Gear Sets
    Berg Gear Copies - Warning
    Liberty Pro Rings and Modified Sliders - FYI
    Gearing
   - Technical Information
    Gear Ratios
    The Berg BUS 600 Adapter
    BUS 600A and BUS 600L Adapter
    Side Cover Savers
    How Does It Bolt In?
   - Bus To Sedan Housing
   - Synchro Hub and Washer
    Ring and Pinion Gear Sets
   - Aftermarket Ring & Pinion
   - Ring & Pinion Gears - Genuine VW Brazil
    Modify Your IRS BUS 4.57:1
    A Needle In A Haystack
   - Technical Information
   - Transaxle Parts
    Super Beetle 3.78 Mainshaft/First Gear
   - Technical Tip
    3.78 Mainshaft
    Conversion Bearing Kit
    Super Duty Berg Close Ratio 1st and 2nd Gear Sets
   - Berg Mainshaft Sets
    FTC Close Ratio 1st and Second Gear Sets
    Heavy Duty Sleeve and Washer
   - Sleeve/ Washers
    Super Duty Keys
    Side Cover Savers2
    Side Cover Nut Conversion
    Side Covers
    Pro Shift Parts
   - Liberty Pro Shift Parts
   - Technical Information
    Super Duty Pinion Bearing Retainer
   - Pinion Bearing Retainers
   - Technical Information
    We No Longer Sell Super Diffs
    Super Duty Berg Axles Technical Tip
   - Axles (per pair)
    Poor Man's Posi (Swingaxle only)
   - Technical Tip
    Magnesium Plate
   - Mag Plate & Welding Rod
    Caster Wedges
   - Caster Wedges/ Bolts
    Avis Front End Adjuster
   - Avis Adjuster
    Front Axle Beam with Adjusters

5 Speed Kits
Special Tools, Tech Manuals
Exhaust Systems, Related Parts
Shifters and Related Parts
Wheelie Bars, Anti-shocker, Drag Fans
Welded Balance Cooling Fans
Type IV Tin Conversion
Shop Supplies
Cases and Related Parts
Labor Section
Factory Volkswagen Parts
Complete Engine Kits
Oils
Metric Hardware

Location: Home » Catalog » Caster Wedges/ Bolts

Caster Wedges/ Bolts

    Caster wedges have been used by VW from the early 50's for cars that wandered in the wind or did not have enough caster from the factory. At least one set was a must if the car was to be driven over 75 MPH. Some cars are manufactured by VW that may have the minimum allowable caster. What this does is allows the car to wander as the speed gets higher or more than normal in a cross wind.
    People that lower the front end of their car, raise the rear end, or both, will aggravate this situation even more. I have seen lowered cars that were almost impossible to keep in one lane at 60 MPH. Some vehicles require more than one caster wedge just to get back to stock and even more to make it safe at 100 MPH. You may need one set of our 3.4 degree and one set of our 2.36 degree. This all depends on the amount of lowering and the maximum speed the car will reach. By adding the proper amount of caster wedges, you tip the beam out at the bottom and increase the caster to eliminate wandering. It is impossible for anyone to guess what "your" car needs. We strongly recommended that the caster be checked before ordering to determine what you actually need. For more information on front and rear suspension see GB 801-SUSPENSION specifically for drag racing or fast street cars. Made in USA by Gene Berg Enterprises.
    Note: 1 One set of 2 is required for a front end unless you are adding wheel stagger to one side or correcting for a bent frame horn.
    Note: 2 GB 681 caster wedges that are 2.36 degrees are about 5.9mm thick and use the factory 90mm bolt. 3.4 degrees are about 8.6mm thick and use GB 681B 100mm long bolts. We also offer 110mm for applications that require stacking more caster wedges. You can calculate what you need by these measurements.
    Note: Shims can be stacked to achieve desired caster.


     Product Name   Description   MSRP Price   Our Price+   Cash Price 
     GB 679-WS  PRESS IN WHEEL STUD, M14-1.5 X 2.20" SET OF 5   $12.78   $9.00   $9.00 
     GB 681  Caster Wedge 2.36 degree ea.   $7.53   $5.30   $5.30 
     GB 681-2  Pair 2.36 degree   $14.20   $10.00   $10.00 
     GB 681-4  2 pr 2.36 degree wedges   $28.40   $20.00   $20.00 
     GB 681B  Pair 100mm beam bolts   $5.33   $3.75   $3.75 
     GB 682  DISCONTINUED. Caster Wedge 3.4 ea.   $0.00   $0.00   $0.00 
     GB 682-2  DISCONTINUED. Pair 3.4 degree   $0.00   $0.00   $0.00 
     GB 682B  Pair 110mm beam bolts   $8.00   $5.82   $5.60 
    Displaying 1 to 8 (of 8 products) Result Pages:  1 

     

     

    Quick Find
     
    Use keywords to find the product you are looking for.
    Advanced Search
    Information
    Business Hours
    Phone Service
    Placing Orders
    Shipping Policies
    Returns For Credit
    Warranty Policy
    Privacy Notice
    Disclaimers
    Contact Us

    Web design and hosting by Canvas Dreams LLC and California web design by Pearl Compass.

    Please contact us about errors or questions. We value your input!

    Any and all references to the company Volkswagen, or the VW name are strictly for reference only. The GENE BERG name and GENE BERG products are protected under trademark, copyright and patent law, any violations will be pursued. GENE BERG ENT. is not a part of any companies mentioned or linked to this website and any beliefs of those companies are not necessarily the beliefs of GENE BERG ENTERPRISES.Site maintained by xanax side effects

    Copyright ©2018 GENE BERG ENTERPRISES all rights reserved