Home » Catalog » Chevy Type-1.4374" OD Inner and Outer Springs  
Product Categories
Apparel
American Hardware
Pistons and Cylinders
Flywheels and Clutches
Gaskets and Bearings
Cranks, Rods and Gland Nuts
Oiling System
Valve Train
   � Oil Additives Mandatory
   � Street Valve Springs
   - Technical Information
   � Race Springs
   - Triple, Stock OD
   � Valve Springs Stock OD
   - Single HD
   � Chevy Type-1.4374" OD Inner and Outer Springs
   � Dual - Inner & Outer, Stock OD
   � Sets of Springs, Retainers & Shims
   - Spring Sets
   � Valve Spring Retainers
   - Valve Retainers
   � Valve Spring Shims
   - Valve Spring Sims
   � Valve Springs
   - Technical Information
   � Springs Require Stronger Steel Pushrods- Warning
   - Warning
   � Mandatory Reading About Cam Sense
   - Technical Information
   � Berg New Billet Cams
   � High Performance Cams
   - Designed for VW Stock Ratio Rocker Arms with Factory 1.1:1 Ratio
   � Camshafts for 1.1:1 Rockers
   � Start of Camshafts
   - Camshaft only
   � Cams Designed for 1.4, 1.45, 1.45, 1.54, Up to 1.65 Ratio Rockers
   � All Cams Below Require:
   � Camshaft to Berg Stroker Crankshaft Clearance
   - Technical Tip
   � Cam Bolt Set
   � Cam Lube
   � Cam Followers (Lifters)
   � Case Bushings
   � Wide Base Lifters
   � Reground Lifters
   � Case Modification of Hydraulic Lifters
   � At this time we do not sell any hydraulic lifters
   � Cam Gears
   � Berg Adjust-A-Gear
   � Adjust-A-Gear Washers
   � Straight Cut Cam Gears
   - Technical Information
   � Adjusting Screws
   - Adjusting Screw Info
   � Gene Berg Cup Screws
   � Super Duty Valve Keepers
   � Valves, Stock Size
   - Stock Size Valves Each
   � Manley Valves, Oversize
   - Manley Stainless Steel Valves Each
   � Other Stainless Valves
   - Stainless Steel Valves ea. ("NON" Manley one piece SS valves. Excellent quality.)
   � Valve Guides
   - Valve Guides and Boss
   � Stock Length Titanium Valves
   - Titanium Valves Ea. Std. VW 3 Groove
   � Titanium Valves with 0.0100" Longer Stem
   - Titanium Plus 0.100"
   � Valve Lash Caps
   � Lash Cap Puller
   � Valve Seats for Oversized Valves
   - Steel Valve Seats (Works with unleaded gas)
   � Silicon Aluminum Bronze Valve Seat Material
   - Brass Seat Material (Sold by the ounce.)
   � Rocker Arm Thrust Washers
   - Thrust Washers
   � Rocker Arm Geometry Shims
   - Rocker Stand Shims
   � Geometry Shims Berg Ratio Rockers
   � Been Clipped Lately?
   - Technical Information
   � Heavy Duty Rocker Arm Shaft Kits
   � Heavy Duty Rocker Arm Shaft Studs
   � Gene Berg Forged High Ratio Rockers
   - Gene Berg Forged Rockers
   � Proper Bushing Used
   � Super Quality Adjusting Screws
   � Why a Ratio Rocker Arm?
   � Gene Berg Forged Rocker Sets
   - Sets Include
   � Special Sets for Moved Exhaust Valves
   � Valve Lift
   - Technical Information
   � What about 1.2 and 1.25 Rockers - FYI
   � Roller Tip Rockers - FYI
   � What Valve Covers to Use
   � Carbon Fiber Pushrods
   - Technical Information
   � Noisy Steel Pushrods? Special FYI
   � How to Make Your Own Test Pushrod - Technical Tip
   � 80,000 PSI Pushrod Kits
   - Pushrods 80,000 PSI
   - Warning
   � About Aluminum Pushrods
   � Superduty 160,000 PSI Racing Pushrods
   - Race Pushrods 160,000 PSI .042" Wall

Pulleys
Carburetion
Programmable Fuel Injection
Electrical Parts
Cylinder Heads
Traction Bars and Mounts
Gear Sets, Tranny Parts, Suspension
5 Speed Kits
Special Tools, Tech Manuals
Exhaust Systems, Related Parts
Shifters and Related Parts
Wheelie Bars, Anti-shocker, Drag Fans
Welded Balance Cooling Fans
Type IV Tin Conversion
Shop Supplies
Cases and Related Parts
Labor Section
Factory Volkswagen Parts
Complete Engine Kits
Oils
Metric Hardware

Location: Home » Catalog » Chevy Type-1.4374" OD Inner and Outer Springs

Chevy Type-1.4374" OD Inner and Outer Springs

    Note 1: Because of supply problems regarding the size and fit, we manufacture our retainers to fit the production run of springs. For this reason the retainer sizes listed may vary slightly. This provides the critical fit from spring to retainer required to stop harmonics and spring chatter. We cannot assure you that others or even previous production runs of our retainers will provide the proper fit. If replacing a set of our springs be sure to have the retainer measurements when ordering so we can assist you in making the proper purchase. SEE GBK kits (previously listed) part numbers for properly matching combinations.
    Note 2: All inner and outer or triple springs require head machining. GB 272A requires that the head be welded in the intake port spring boss area, re-porting and machining. Use GB 706 tool and space out the blade to achieve this larger diameter (1.445") or purchase GB 706CH blade.
    Note 3: For many applications we have found that captivating the spring at the head end will increase life and further stop harmonics. See LA HEAD320 for welding in spring retaining cups.


    1054 - Unknown column 'final_price' in 'order clause'

    select DISTINCT p.products_image, p.products_model, products_description.products_name, p.products_id, products_description.products_description, products_to_categories.categories_id, p.products_price, p.products_price_msrp, p.products_price_cash from products_description INNER JOIN products p ON products_description.products_id = p.products_id INNER JOIN products_to_categories ON products_to_categories.products_id = p.products_id where p.products_status = '1' and products_to_categories.categories_id = '154' order by final_price , pd.products_name limit 0, 1000

    [TEP STOP]