Home » Catalog » Technical Information  
Product Categories
Apparel
American Hardware
Pistons and Cylinders
Flywheels and Clutches
Gaskets and Bearings
Cranks, Rods and Gland Nuts
Oiling System
Valve Train
   • Oil Additives Mandatory
   • Street Valve Springs
   - Technical Information
   • Race Springs
   - Triple, Stock OD
   • Valve Springs Stock OD
   - Single HD
   • Chevy Type-1.4374" OD Inner and Outer Springs
   • Dual - Inner & Outer, Stock OD
   • Sets of Springs, Retainers & Shims
   - Spring Sets
   • Valve Spring Retainers
   - Valve Retainers
   • Valve Spring Shims
   - Valve Spring Sims
   • Valve Springs
   - Technical Information
   • Springs Require Stronger Steel Pushrods- Warning
   - Warning
   • Mandatory Reading About Cam Sense
   - Technical Information
   • Berg New Billet Cams
   • High Performance Cams
   - Designed for VW Stock Ratio Rocker Arms with Factory 1.1:1 Ratio
   • Camshafts for 1.1:1 Rockers
   • Start of Camshafts
   - Camshaft only
   • Cams Designed for 1.4, 1.45, 1.45, 1.54, Up to 1.65 Ratio Rockers
   • All Cams Below Require:
   • Camshaft to Berg Stroker Crankshaft Clearance
   - Technical Tip
   • Cam Bolt Set
   • Cam Lube
   • Cam Followers (Lifters)
   • Case Bushings
   • Wide Base Lifters
   • Reground Lifters
   • Case Modification of Hydraulic Lifters
   • At this time we do not sell any hydraulic lifters
   • Cam Gears
   • Berg Adjust-A-Gear
   • Adjust-A-Gear Washers
   • Straight Cut Cam Gears
   - Technical Information
   • Adjusting Screws
   - Adjusting Screw Info
   • Gene Berg Cup Screws
   • Super Duty Valve Keepers
   • Valves, Stock Size
   - Stock Size Valves Each
   • Manley Valves, Oversize
   - Manley Stainless Steel Valves Each
   • Other Stainless Valves
   - Stainless Steel Valves ea. ("NON" Manley one piece SS valves. Excellent quality.)
   • Valve Guides
   - Valve Guides and Boss
   • Stock Length Titanium Valves
   - Titanium Valves Ea. Std. VW 3 Groove
   • Titanium Valves with 0.0100" Longer Stem
   - Titanium Plus 0.100"
   • Valve Lash Caps
   • Lash Cap Puller
   • Valve Seats for Oversized Valves
   - Steel Valve Seats (Works with unleaded gas)
   • Silicon Aluminum Bronze Valve Seat Material
   - Brass Seat Material (Sold by the ounce.)
   • Rocker Arm Thrust Washers
   - Thrust Washers
   • Rocker Arm Geometry Shims
   - Rocker Stand Shims
   • Geometry Shims Berg Ratio Rockers
   • Been Clipped Lately?
   - Technical Information
   • Heavy Duty Rocker Arm Shaft Kits
   • Heavy Duty Rocker Arm Shaft Studs
   • Gene Berg Forged High Ratio Rockers
   - Gene Berg Forged Rockers
   • Proper Bushing Used
   • Super Quality Adjusting Screws
   • Why a Ratio Rocker Arm?
   • Gene Berg Forged Rocker Sets
   - Sets Include
   • Special Sets for Moved Exhaust Valves
   • Valve Lift
   - Technical Information
   • What about 1.2 and 1.25 Rockers - FYI
   • Roller Tip Rockers - FYI
   • What Valve Covers to Use
   • Carbon Fiber Pushrods
   - Technical Information
   • Noisy Steel Pushrods? Special FYI
   • How to Make Your Own Test Pushrod - Technical Tip
   • 80,000 PSI Pushrod Kits
   - Pushrods 80,000 PSI
   - Warning
   • About Aluminum Pushrods
   • Superduty 160,000 PSI Racing Pushrods
   - Race Pushrods 160,000 PSI .042" Wall

Pulleys
Carburetion
Programmable Fuel Injection
Cylinder Heads
Electrical Parts
Traction Bars and Mounts
Gear Sets, Tranny Parts, Suspension
5 Speed Kits
Special Tools, Tech Manuals
Exhaust Systems, Related Parts
Shifters and Related Parts
Wheelie Bars, Anti-shocker, Drag Fans
Welded Balance Cooling Fans
Type IV Tin Conversion
Shop Supplies
Cases and Related Parts
Labor Section
Factory Volkswagen Parts
Complete Engine Kits
Oils
Metric Hardware

Location: Home » Catalog » Technical Information

Technical Information

    Many people have the misconception that all you do is put in a bigger cam to get more power. WRONG! The VW is extremely sensitive to cam changes. Care must be taken or you will end up with an engine that will not idle correctly or perhaps not at all. You could even end up with much less power than your stock engine provided. All higher performance camshafts are designed to reduce low end power and add top end. If improper combinations are chosen you will lose the low end and have no more improvement or little gain in the higher RPM. To maintain or improve the low end that has been lost other modifications are mandatory such as adding CC’s to the engine with bigger bore and or a stroker crankshaft. For this reason a good general rule for street engines is to select the camshaft last. You must select ALL other components first and then the cam can be selected. The only exception to this rule is when the engine is for race use only.
    There are some general rules you can rely on. First, the lift can usually be increased with little effect on the low end power. This will allow higher RPM provided the head will continue to flow at the higher lifts.
    There is a diminishing area of gain with extra lift if proper head work is not performed. The more carburetion and head work, the more cam duration that can be used provided a correct balance of valve size, intake, and exhaust size is maintained. This balance is critical to both the functioning of the engine, tuning and running temperature.
    The bore/stroke combination is also related to this area because the larger the engine the harder and faster it will suck through a specific port. So, often people get cams that seem to run fairly well. However, they had nothing to compare to, so they never knew whether a better combination could have given them more all around driveability throughout the RPM range for the same investment. This is one of the major reasons we recommend being clear about the combination you want as it allows both of us to look at the complete road map of the engine, results desired, budget and what will be produced. You must understand that asking for a cam recommendation without every possible fact creates further guess work on your part and we will only assist you with a cam selection at the time you are placing your cam order.
    A good example of the importance of this was when I put a GB 297 cam in a 69 X 88 (1679cc) engine with single port heads and a Holley 300 CFM carb. It ran strong, but idled like a top fuel racer, rough and way too high. It jerked and bucked at a steady 35 MPH in 3rd gear around town. Miserable to drive in 3rd yet the RPM was too high for 2nd gear. I installed the dual Kadrons, and it was the difference between night and day. It still had a small amount of the rough idle, yet was fairly smooth to drive.
    Next, I put on dual port heads and kept the Kadrons. Again, even smoother, with only a small amount of rough idle. Then the GB 479U Berg 42 special carb kit was installed and the engine was smoother than stock. You could now drive it in 4th gear at 35 MPH. The idle was actually lower and smoother than the stock cam in a stock engine. Then I installed a GB 300 cam. Still very smooth and driveable with only a slight trace of rough idle. This alone should demonstrate that the proper combination is critical to your project. Yes, the proper selection will provide good smooth power and driveability. It pays to get all of your parts from a supplier of tested and proven engine kits all at one place so they will match and provide the performance you are looking for within your budget.
    Also see GB 801-CAM and GB 801-HEADS for additional information.


    There are no products to list in this category.

     

     

    Quick Find
     
    Use keywords to find the product you are looking for.
    Advanced Search
    Information
    Business Hours
    Phone Service
    Placing Orders
    Shipping Policies
    Returns For Credit
    Warranty Policy
    Privacy Notice
    Disclaimers
    Contact Us

    Web design and hosting by Canvas Dreams LLC and California web design by Pearl Compass.

    Please contact us about errors or questions. We value your input!

    Any and all references to the company Volkswagen, or the VW name are strictly for reference only. The GENE BERG name and GENE BERG products are protected under trademark, copyright and patent law, any violations will be pursued. GENE BERG ENT. is not a part of any companies mentioned or linked to this website and any beliefs of those companies are not necessarily the beliefs of GENE BERG ENTERPRISES.Site maintained by xanax side effects

    Copyright ©2018 GENE BERG ENTERPRISES all rights reserved