Home » Catalog » Technical Information  
Product Categories
Apparel
American Hardware
Pistons and Cylinders
Flywheels and Clutches
Gaskets and Bearings
Cranks, Rods and Gland Nuts
Oiling System
Valve Train
Pulleys
Carburetion
    Throttle shafts for Berg IDA
    What Fuel Hose?
    Preventive Maintenance Tip About the Gas Tank Fuel Filter
    Jet-A-Vator
    Butterflies for Berg IDA
    32/34 PDSIT
    Carburetor Linkages Fan Housing Mount
   - Linkages for 36hp Chinese dog house shroud
   - Linkages for VW fan housing mount.
    Carb-to-Carb Mount
    Center Pull
    Stock Kadron Linkage
    Carburetor Linkage Arms, Rods and Ball Joints
    Linkage Arms - FYI
    Carburetion for the VW Air Cooled Engines
   - Technical Information
    Carbs Run Anything
    Carburetors and Kits
   - Carburetors
    Modify Your 48mm to 51mm
   - Carb Labor
    The Berg IDA Carb
   - Berg IDA Carburetor Sizes
    Carb Modifications
    VW Factory Dual 32mm Solex Carb Kit
    Polished Billet Aluminum New Linkage Pivot
    Air Cleaners
    Carburetor Kits
   - Berg Weber Dual Carb Kits
    Air Cleaner Vent Fitting
    Replacement Elements
    Berg 48 IDA Velocity Stack
    Dual 40mm Solex
   - Technical Information
    48IDA Venturis
    42 DCNF and Berg Specials
   - 42 DCNF
    Dual 40mm Solex Sets - FYI
    Carb Gasket Kits
   - Rebuild and Gasket kits
    Dual 40mm Solex Carb Kits
    Weber, Dellorto and Solex - FYI
   - Dual Gas Line
    Berg/Weber Dual Carb Kits
    But I Have To Have A Choke!
   - Technical Information
    Jetting Information - FYI
    What Fuel Pump to Use
    I Use the Stock Pump
    What Electric Pump to Use
    Other Types of Regulators
    Gas Line Size
   - Technical Information
    Electric Fuel Pumps, Holley Pumps and Parts
    Faucet Fuel Pumps
    Vent Fitting
    Replacement Elements, Oil and Cleaner
    Berg 42 Velocity Stacks
    Berg Billet Aluminum Velocity Stacks
    Stock 48 IDA Weber Velocity Stack
    Carb Covers for 48 IDA and Berg 58
    Secondary Venturis
   - Berg Auxiliary Venturis
    Venturis
    Venturis for 40, 42 DCNF and Berg Special
    Venturis for 48 IDA Weber
    Venturis for IDA Berg Carbs
    Jets - Main, Air and Idle
   - 42 Weber Type Air Jets
   - 42 Weber Type Idle Jets
   - 42 Weber Type Main Jets
   - 48 Weber Type Air Jets
   - 48 Weber Type Idle Jets
   - 48 Weber Type Main Jets
   - Solex Air Jets
   - Solex Idle Jets
   - Solex Main Jets
    Ball Type Needle and Seat
   - Dellorto
   - Needle and Seats
   - Solex
   - Stock 48 IDA
   - Weber
    Weber
    Solex
    Dellorto
    Stock 48 IDA
    Tall Jet Holder
   - Berg Tall IDA Type Emulsion Tube Holder
    Emulsion Tubes for 40/44 IDF, 48 IDA/Berg IDA (sold per each)
   - Weber & Berg Emulsion Tubes
    Customer Support
    Carb Schematic Numbers to Weber and Berg Part Numbers
   - 42 DCNF & Berg Specials
    40/44/48 IDF
    48 IDA
    Adjustable Accelerator Pump Ramp
   - Carburetor Parts
    Banjo and Tee Fittings
   - Technical Tip
    Carb Gasket Kits (for one carb)
    Carb Rebuild Kits (per carb)
    Float Height Gauge
    Weber Parts
   - Additional Carburetor Parts
    Gas Line Kits
    Fuel Pump Block Off
    Berg Super Strength Dual-Carb Manifold Sets
   - Manifolds for dual carb (Sold in pairs)

Programmable Fuel Injection
Cylinder Heads
Electrical Parts
Traction Bars and Mounts
Gear Sets, Tranny Parts, Suspension
5 Speed Kits
Special Tools, Tech Manuals
Exhaust Systems, Related Parts
Shifters and Related Parts
Wheelie Bars, Anti-shocker, Drag Fans
Welded Balance Cooling Fans
Type IV Tin Conversion
Shop Supplies
Cases and Related Parts
Labor Section
Factory Volkswagen Parts
Complete Engine Kits
Oils
Metric Hardware

Location: Home » Catalog » Technical Information

Technical Information

    Selection of carburetion is extremely critical on the air cooled engine. To ensure long life the fuel/air volume must match the engine demands throughout the RPM range to assist in proper cooling. The fuel curve (flow vs. RPM and vacuum rate) must be extremely close or damage that cannot be detected by seat of the pants methods will occur. The vacuum signal the engine sends to the carb will be different on every engine dependent upon things such as piston speed, valve size, port size and velocity, carb size and venturi, exhaust size and design, and on, and on. The European new car manufacturers often have to change the carbs during production runs of the engine as the ports of the head and intake manifold change during production. The 44 IDF carb and most Dellortos are for the 1600 Fiat Abarth engines and the Weber alone has 39 different versions of the same carb for the same engine.
    As the vacuum rate changes in production through tooling wearing out they recircuit and rejet the carb to perform properly providing the correct amount of fuel and air. When this is needed they will re-number the carb and it will now fit a group of engines from such and such serial number to another such and such serial number. When needed they will then make changes again to cover the next group of engines. Without redrilling the circuitry and re-jetting the carbs to match the signal sent from the engine's vacuum rate the carb is unable to deliver what the engine really requires.
    Many engines may seem to run OK, yet may not be correctly distributing the needed fuel/air ratio for the horsepower and cooling. Few people realize that an extremely large part of the VW air cooled engine's cooling is derived from the proper carburetion. That is why the engine should never be leaned out to optimize mileage, it is simply false economy. It may provide up front savings on gas but is costing far more later to replace the prematurely worn or damaged parts. Instead of getting 80,000 to 100,000 or more miles of life out of the engine, problems show up in as little as 10,000 to 40,000 miles. We spend a great deal of time on the phone with many of these people telling us that their car runs perfect with their 40/44/48 IDF Fiat Webers, 40/45/48 Dellortos, or their Holley Weber Pinto 2300cc progressive carb used in both dual carb as well as single center mount applications.
    Then in the next breath they tell us the reason they called was because the engine is overheating, has blow-by in only 5000 miles, etc., has already failed in some way, or required a premature rebuild. These failures are often not related to the improper pounds of fuel and air per HP, however, in most cases that is what causes these failures. I, personally, find that as a poor return on any investment.
    For maximum life it is necessary to use carbs with the progression circuit and fuel flow curve to match the VW engine. No Weber or Dellorto carb I have ever seen was made with the proper circuitry for the needs of a VW engine. I only found two Webers that did not already have way too large of passages for the VW's needs. We are the only company able to offer properly circuited carburetion for the VW air cooled engine and modify our carbs to work with specific engine sizes, head combinations and matching components.
    This gives you smooth all around performance and correct fuel/air ratio through the complete RPM range. This is one reason we limit the types of carbs we recommend and sell, because all of the other cheaper carbs that already have circuitry holes, which are too large, cannot be reduced to the VW engine's requirements.
    Head temperature is the air cooled engine's worst enemy. It causes more damage than all other failures combined and is seldom identified as the problem. This is one reason the carburetion circuitry must precisely match the requirements of the VW air cooled engine. The pounds of fuel/air per hour per horsepower distributed to the engine is responsible for up to 50% of the cooling efficiency.
    My only exception to this rule has been in race applications. These engines operate over a much narrower RPM range and can be adequately tuned to work in that range only and are commonly apart for other repairs long before the damage can be done by the carburetion. Off-road or road racing applications should use the 40/44/48 IDF or such Dellorto carbs due to their superior float design for rough terrain or hard cornering.


    There are no products to list in this category.

     

     

    Quick Find
     
    Use keywords to find the product you are looking for.
    Advanced Search
    Information
    Business Hours
    Phone Service
    Placing Orders
    Shipping Policies
    Returns For Credit
    Warranty Policy
    Privacy Notice
    Disclaimers
    Contact Us

    Web design and hosting by Canvas Dreams LLC and California web design by Pearl Compass.

    Please contact us about errors or questions. We value your input!

    Any and all references to the company Volkswagen, or the VW name are strictly for reference only. The GENE BERG name and GENE BERG products are protected under trademark, copyright and patent law, any violations will be pursued. GENE BERG ENT. is not a part of any companies mentioned or linked to this website and any beliefs of those companies are not necessarily the beliefs of GENE BERG ENTERPRISES.Site maintained by xanax side effects

    Copyright ©2018 GENE BERG ENTERPRISES all rights reserved