Home » Catalog » Tools  
Product Categories
Apparel
American Hardware
Pistons and Cylinders
Flywheels and Clutches
Gaskets and Bearings
Cranks, Rods and Gland Nuts
Oiling System
Valve Train
Pulleys
Carburetion
Programmable Fuel Injection
Cylinder Heads
Electrical Parts
Traction Bars and Mounts
Gear Sets, Tranny Parts, Suspension
5 Speed Kits
Special Tools, Tech Manuals
    17mm Trans Drain Tool
    Flywheel Puller
    Transmission Fixture Test Driver
    Tools - Gene Berg Flycutter
   - Tools
    Drill Press Flycutter
   - Tools
    Mill Set
    Additional Cutter Heads
    Semi-Hemi Cutter
    Special Centers
    Lash Cap Puller
    Replacement Blades
    Boring - Deck Plate
   - Special Note
    Valve Guide Boss Cutter
    Off Road Race Engines Require a Seal
   - Technical Information
    Pulley Seal Tool
    Pulley Seals
   - Warning - No Bolt In Seal/Pulleys
    Coring Drill
    Ring Compressor Set
    Gear Puller
    Cam Follower - Case Hole Cutter
    Flywheel Holder
    End Play Measuring Tool
    Universal Pulley Puller
    Valve Spring Remover
    Lifter Retaining Springs
    Flywheel Seal Tool
    Deck Measuring Tool
    Oil Relief Cup Puller
    Oil Filler Nut Wrench
    Distributor Drive Puller
    Axle Nut Driver Wrench
    Clutch Cable Adjusting Wrench
    Valve Adjusting Wrench
    22mm Piston Pin Driver
    8mm Guide Driver
    Clutch Alignment Tools
    CC Kits and Parts
    Synchrometers
    Flywheel - Crank Drill Fixture
    Gear Ratio Computer
   - Ratio Computer
    Books and Literature
    Berg's Information Copyrighted Materials
    Berg Book of Instructions
    Berg Technical Sets
   - Individual Articles
   - Tech Articles
    Individual Articles
    Technical Materials
    Have your own computer?
    Gear Ratio Program
   - Gear Ratio Program
    HP for DOS
    California Look VW Book
    Bentley VW Workshop Manuals

Exhaust Systems, Related Parts
Shifters and Related Parts
Wheelie Bars, Anti-shocker, Drag Fans
Welded Balance Cooling Fans
Type IV Tin Conversion
Shop Supplies
Cases and Related Parts
Labor Section
Factory Volkswagen Parts
Complete Engine Kits
Oils
Metric Hardware

Location: Home » Catalog » Tools

Tools

    I developed (originated) this tool in 1961 because it was impossible to find anyone with a mill to bore the case and heads so I could install the larger Corvair pistons and cylinders on my 40 HP engine. It had to be a rugged precision tool that would provide years of shop use with a quality drill press, as we did not have access to a milling machine. Features rugged cast aluminum housing with all 4 feet, 1-1/2" case hardened (heat treated), centerless ground shaft that is running in silicon bronze bushings which provide years of trouble free accurate cutting. I installed a National oil seal in the base's bottom that keeps cuttings or contamination from damaging these bushings and/or the shaft. It has a positive shaft collar stop for exact duplication from hole to hole depth when flycutting. For those who do not have a friction controller on their drill press spindle, a second collar stop can be used for this feature.
    Uses adjustable cutters in the blade holder. Once set the cutter head screws onto the driving shaft. The cutter heads are designed with proper mass (much thicker than our competitors) to provide smooth cuts for boring or just a simple cleanup flycut on a used head. Flycuts and/or bores heads (up to standard 92mm) for more CR or larger bores and bores cases for larger (up to standard 92mm) cylinders without removing studs. Semi-Hemi cutting for properly lowering the CR can be done by purchasing our Semi-Hemi cutter.
    Comes with universal centering device GB 702F, and 2 GB 701 cutter heads for you to set at the needed size. See GB 702's for precision centers for specific size bores. I, personally, recommend purchasing the 15/1600cc precision head center GB 702-855. Additional cutter heads can be purchased and set to needed sizes eliminating the need to reset over and over again. This tool requires a perfectly flat parallel surface for the feet to bolt down to in order to provide parallel seating surfaces for the cylinders. For heads from 1967-on with the 6 locating knobs the GB 705 boring plate is required or the heads must be milled flat. This tool is a precision quality product, not a cheap toy like most people sell! Get a genuine GENE BERG FLYCUTTER. Made in USA by Gene Berg Enterprises.
    Cutting heads for 94mm P/C. It is not possible to have this tool do both heads and case work for 94mm P/C's. When the feet are clearanced to fit the 94mm heads they will be too large to set on the case seating surface regardless of bore size. To get around this problem purchase GB 700B-94 base.


    There are no products to list in this category.

     

     

    Quick Find
     
    Use keywords to find the product you are looking for.
    Advanced Search
    Information
    Business Hours
    Phone Service
    Placing Orders
    Shipping Policies
    Returns For Credit
    Warranty Policy
    Privacy Notice
    Disclaimers
    Contact Us

    Web design and hosting by Canvas Dreams LLC and California web design by Pearl Compass.

    Please contact us about errors or questions. We value your input!

    Any and all references to the company Volkswagen, or the VW name are strictly for reference only. The GENE BERG name and GENE BERG products are protected under trademark, copyright and patent law, any violations will be pursued. GENE BERG ENT. is not a part of any companies mentioned or linked to this website and any beliefs of those companies are not necessarily the beliefs of GENE BERG ENTERPRISES.Site maintained by xanax side effects

    Copyright ©2018 GENE BERG ENTERPRISES all rights reserved