Product Name |
Description |
MSRP Price |
Our Price+ |
Cash Price |
LA CRANK001 |
CHECK CRANK FOR STRAIGHTNESS |
$50.00 |
$34.95 |
$34.95 |
LA CRANK002 |
CHECK JOURNAL SIZES |
$43.00 |
$29.95 |
$29.95 |
LA CRANK008 |
Install 8-11/32" press fit dowels. Plus price of dowels. Read all about proper doweling in the crank section of this catalog. |
$83.25 |
$65.00 |
$65.00 |
LA CRANK010 |
Remove crank timing gears. |
$35.75 |
$25.00 |
$25.00 |
LA CRANK011 |
Install crank timing gears, plus bearings. |
$49.98 |
$34.95 |
$34.95 |
LA CRANK012 |
Remove crank timing gears. Install new bearing, glassbead and re-install gears (on same or another crank). |
$60.00 |
$45.00 |
$45.00 |
LA CRANK014 |
Set end play on crank to flywheel. Install the flywheel and properly torque the gland nut. This is done after you have assembled the short block. We can also perform this function with the engine apart for those of you that do not have a way to do it at home. We clean the crank, oil and mark the bearing at the split lines for easy installation into the case when you get it home. We install the bearing, set the end play, clean and lube the bearing in the nut, Loctite the nut/washer to crankshaft and properly torque. We then put the crankshaft in a plastic bag to keep clean until you receive it and are ready to install it in the block. Price plus shims, seal, etc. |
$87.00 |
$60.00 |
$60.00 |
LA CRANK014W |
Same as LA CRANK014 but done with our wedgemated crank and flywheel. |
$91.55 |
$70.00 |
$70.00 |
LA CRANK015 |
Same as LA CRANK014 but done with engine apart. |
$106.85 |
$75.00 |
$75.00 |
LA CRANK015W |
Same as LA CRANK015 but done with our wedgemated crank and flywheel. |
$121.15 |
$90.00 |
$90.00 |
LA CRANK018 |
Micro-polish and check journal sizes. |
$49.98 |
$34.95 |
$34.95 |
LA CRANK020-C |
Regrind your crank to next undersize. Micro-polish is additional, see LA CRANK018. Turnaround time depends on our production schedule. This service offered only to genuine VW stock crankshafts or to a previous made Berg crank. |
$182.20 |
$132.50 |
$132.50 |
LA CRANK026 |
Magnaflux customers crankshaft |
$64.28 |
$44.95 |
$44.95 |
LA CRANK100 |
Glass bead crank before grinding. |
$39.05 |
$28.39 |
$28.39 |
LA CRANK102 |
Tape journals and glass bead crank. |
$58.55 |
$42.59 |
$42.59 |
LA CRANK104 |
Tape and shot-peen crank. Done only to our processed crankshafts. Not beneficial when done to a stock or stock counterweighted crankshaft. |
$97.60 |
$70.98 |
$70.98 |
LA CRANK106 |
Stress relieving. Normally done to a crank with a smoked journal or a journal that has to be welded. A must before re-heat treatment (must be re-nitrided after). Removes stress bending caused by a burnt rod bearing or the crank being bent. Allow extra time, as this must be done with a production run. |
$97.60 |
$70.98 |
$70.98 |
LA CRANK108 |
Nitride Type I, II, III. Nitride includes taping journals and shot peening crank, check and correct straightness of the crank, butt grind and fine micro-polish journals after nitriding. You must clean journal oil holes before you re-install crank. Allow extra time, as this must be done with a production run. |
$165.20 |
$120.12 |
$120.12 |
LA CRANK108-1 |
Nitride Type I, II, III. Nitride includes taping journals and shot peening crank, check and correct straightness of the crank, butt grind and fine micro-polish journals after nitriding. You must clean journal oil holes before you re-install crank. Allow extra time, as this must be done with a production run. |
$720.75 |
$524.16 |
$524.16 |
LA CRANK110A |
TIGHTEN WEDGE |
$106.50 |
$75.00 |
$75.00 |
LA CRANK200 |
Reprocess a Gene Berg crankshaft. This is required any time you burn a rod to remove the overheat treatment from the burning rod and the bending stress. Stress relieve crank to remove old (and to prevent over hardening) heat treat and stress. Regrind next undersize. Nitride, micro-polish, straighten, shot peen, re-balance, check for run out of flywheel. (Send your flywheel with your crank). Correcting flywheel run out, (if needed) is additional, at shop labor rate per hour. |
$536.25 |
$390.00 |
$390.00 |
LA CRANK201 |
As LA CRANK200 when a burned rod requires welding, rough grind, straightening, plus all previously listed functions. |
$607.75 |
$442.00 |
$442.00 |
LAS CRANK015 |
STRAIGHTEN CRANK. |
$71.00 |
$50.00 |
$50.00 |