Home » Catalog » Transaxle  
Product Categories
American Hardware
Pistons and Cylinders
Flywheels and Clutches
Gaskets and Bearings
Cranks, Rods and Gland Nuts
Oiling System
Valve Train
Programmable Fuel Injection
Electrical Parts
Cylinder Heads
Traction Bars and Mounts
Gear Sets, Tranny Parts, Suspension
5 Speed Kits
Special Tools, Tech Manuals
Exhaust Systems, Related Parts
Shifters and Related Parts
Wheelie Bars, Anti-shocker, Drag Fans
Welded Balance Cooling Fans
Type IV Tin Conversion
Shop Supplies
Cases and Related Parts
Labor Section
    Labor - Dyno Time
   - Example of Note Enclosure
    The Balancing of Your Engine -FYI
    Labor - Balancing
   - Balancing
    Balancing - Individual Parts
    Your Balanced Engine - Special Note
    Labor - Cam
   - Cam
    Labor - Carb
   - Carb
    Labor - Case
   - Case
    No Stroker Crankshafts
   - Special Note
    Hydraulic Lifters
   - Technical Information
    Line Bored Cases - Special Note
    Labor - Clutch
   - Clutch
    Labor - Crankshaft
   - Crankshaft
    Labor - Cylinder
   - Cylinder
    Labor - Fan
   - Fan
    Labor - Flywheel
   - Flywheel
    Labor - Head
   - Head
    Valve Job
    Periodic Head Work
   - Technical Information
    Labor - Intake Manifold
   - Intake Manifold
    Labor - Piston
   - Piston (Set of 4)
    Notch Locations
   - Technical Information
    Labor - Pulley
   - Pulley
    Labor - Pushrods
   - Pushrods
    Labor - Rod
   - Rod
    Labor - Spacers
   - Spacer
    Labor - Rocker Arm
   - Rocker Arm
    Labor - Tinware
   - Tinware
    Labor - Transaxle Parts
   - Transaxle
    Labor - Turnaround Time

Factory Volkswagen Parts
Complete Engine Kits
Metric Hardware

Location: Home » Catalog » Transaxle


    Note: This service done only when we modify our own for inventory or have an ample number of customer's shafts to warrant set up time of the 3 machines. Delivery may take up to 2 months.

     Product Name   Description   MSRP Price   Our Price+   Cash Price 
     B5L 660  MODIFY PINION FOR 5 SPEED   $875.00   $600.00   $600.00 
     B5L 662  MODIFY MAINSHAFT FOR 5 SPEED   $875.00   $600.00   $600.00 
     LA TRANS010  Weld 3rd or 4th syncro hub or pro ring onto Berg gear set. We press the hub off your old gear (unless you purchase GB 659), press onto the new gear and weld to prevent slipping. ID size of the new gear is honed back to size (always shrinks). If this ID size is not corrected the gear set will be far noisier than stock. We then re-grind to stock height. Per 1 gear.   $60.35   $42.50   $42.50 
     LA TRANS010-2  As above, welding two gears (such as 3rd and 4th) at one time. $70 on new gears/hubs.   $107.25   $78.00   $78.00 
     LA TRANS020  Modify your 3.78 (splined at 3rd and 4th) mainshaft to the keyed type that accepts most all close ratio 3rd and 4th gears. You must convert back to the early keyed type mainshaft bearing and intermediate housing. We grind it to size, recut new snap ring groove, undercut reliefs and cut new woodruff key slot. From time to time we will have good used mainshafts that we can exchange. If you do not state that we must do the labor to your shaft we will exchange it if we have one to exchange.   $355.00   $250.00   $250.00 
     LA TRANS022  Mag used mainshaft   $21.45   $25.00   $25.00 
     LA TRANS025  Additional cost to convert splined mainshaft to keyed for 5 speed.   $39.85   $28.96   $28.96 
     LA TRANS030  REMOVE HUB FROM GEAR   $28.60   $20.00   $20.00 
     LA TRANS035  "Mate a 2.25 mainshaft to any VW 1st gear mainshaft. We cut and bore the 2.25 mainshaft, grind 1st gear mainshaft to the correct press fit, press together, weld (under submerged arc), remachine and straighten if necessary. Labor price only. Delivery may be up to two months. If sending in these parts, please count the teeth (16 on the mainshaft 2nd gear) to be sure you have the proper ratio. If the 2.25 mainshaft is the late splined type, it will also require LA TRANS020 to accept close ratio gears."   $858.00   $600.00   $600.00 
     LA TRANS037  Install Liberty pro ring. We grind the syncro teeth off a 2nd gear, press on the pro ring and spot weld it. We then hone the gear back to proper size. Labor price only.   $119.55   $86.94   $86.94 
     LA TRANS040  Splice 4.57 pinion shaft. You must furnish the 4.57 and the sedan pinion you want spliced together.   $858.00   $600.00   $600.00 
     LA TRANS055  Cut back slider reverse gear teeth to clear 091, GB 663(?) or FTC wider than stock 1st gear on the mainshaft.   $5.20   $30.00   $30.00 
     LA TRANS070  Double snap ring   $143.00   $104.00   $104.00 
    Displaying 1 to 13 (of 13 products) Result Pages:  1 



    Quick Find
    Use keywords to find the product you are looking for.
    Advanced Search
    Business Hours
    Phone Service
    Placing Orders
    Shipping Policies
    Returns For Credit
    Warranty Policy
    Privacy Notice
    Contact Us

    Web design and hosting by Canvas Dreams LLC and California web design by Pearl Compass.

    Please contact us about errors or questions. We value your input!

    Any and all references to the company Volkswagen, or the VW name are strictly for reference only. The GENE BERG name and GENE BERG products are protected under trademark, copyright and patent law, any violations will be pursued. GENE BERG ENT. is not a part of any companies mentioned or linked to this website and any beliefs of those companies are not necessarily the beliefs of GENE BERG ENTERPRISES.

    Copyright ©2021 GENE BERG ENTERPRISES all rights reserved